Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You may find that your garage door opener has been providing you issues, so you need to fix it. You can fix it by replacing a motherboard, a photo-eye sensing unit, the main drive gear, or the set-limit switches. You can also inspect if the safety and security sensors are functioning properly.

Changing a circuit board

Changing a motherboard for your garage door opener requires a couple of actions and also devices. First, you require to switch off the circuit breaker and separate any type of cables. Next off, open the motherboard cover. This will certainly aid you to identify the issue as well as determine if you require a brand-new board. Next off, get rid of the old board and its wire adapters.

You can after that continue to change the motherboard. The replacement process is simple and also takes about 10 mins. A brand-new circuit card will set you back concerning $80. To safeguard your new motherboard from power surges, you can buy a rise protector.

Replacing a photo-eye sensor

Changing a photo-eye sensor can be a rather basic task. Initially, remove the sensing unit from the door and also ensure it is positioned appropriately. If the sensor is angled whatsoever, it might not be obtaining the appropriate signal, which might be triggering the strobe lights. If you see that the photo-eyes run out alignment, you might need to have a professional come as well as repair the problem.

The photo-eye sensing unit contains two items that mount on the outside of the door tracks and towards the flooring. The photo eyes will have a tiny LED light and also ought to be strong in color. If the light is blinking, its most likely the photo-eye is defective as well as will need to be changed.

Replacing a major drive equipment

To replace a garage door opener main drive equipment, start by getting rid of the cap from the chain pulley. Next off, eliminate both screws holding the drive equipment to the sprocket setting up. Now, you can loosen the three tension pins. Press them from both sides and after that remove them. After that, disconnect the 3 cables from the garage door opener electric motor. These wires should be white, red, as well as blue.

When you have actually removed the old gear, mount a brand-new one. Make sure to grease it well. Put the brand-new gear into the shaft, making sure to line up the installing holes. See to it the gear as well as gear setting up are positioned correctly to guarantee smooth operation. Next, use a hammer and also a nail to drive a pin into the brand-new gear.

Readjusting the set-limit switches

The very first thing you must do if your garage door is not working correctly is to check the set-limit buttons. You might need to readjust them to ensure that the door closes earlier or stops prior to it reaches the flooring. You can examine this by looking at your garage doors guidebook or online.

To change the set-limit switches, youll need a screwdriver or socket. Adjust the handle clockwise or counterclockwise till the door goes up as well as stops, or minimizes its distance. To check for proper travel range, gauge the gap from the bottom of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Key St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *

Back To Top